Proxxon 37088 Instruction Manual download pdf

- 5 -

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Follow

instructions for lubricating and changing

accessories.

15. DISCONNECT TOOLS before servicing; when

changing accessories, such as blades, bits, cutters,

and the like.

16. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in off position

before plugging in.

17. USE RECOMMENDED ACCESSORIES. Consult the

owner's manual for recommended accessories. The

use of improper accessories may cause risk of

injury to persons.

18. NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use of

the tool, a guard or other part that is damaged

should be carefully checked to determine that it will

operate properly and perform its intended function

-check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A

guard or other part that is damaged should be

properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or

cutter against the direction of rotation of the blade

or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don't leave tool until it comes

to a complete stop.

Table 1

Minimum gage for cord

Ampere Rating Volts Total length of cord in feet

120 V 25 ft. 50 ft. 100 ft. 150 ft.

240 V 50 ft. 100 ft. 200 ft. 300 ft.

More Not More AWG

Than Than

0 6 18 16 16 14

610 18161412

10 12 16 16 14 12

12 16 14 12 Not Recommended

Additional safety instructions

IMPORTANT

1. Ensure the workplace is tidy.

2. Check the unit for damage before use

3. (connection cable, protective devices, etc.), have

defective parts replaced by qualified personnel.

4. This unit corresponds to the pertinent safety

regulations. Repairs (e.g., replacement of the

power supply lead) may only be performed by a

qualified electrician

5. Never work without the safety equipment fitted.

6. Do not use electrical power tools in the rain, in

damp surroundings or in the vicinity of flammable

liquids or gases.

7. Only use the tool when the handle is dry and free

from grease.

8. Avoid contact with earthed components,

e.g., pipes, radiators, ovens and refrigerators.

9. Protect the connection lead from heat and sharp

edges and route it so it cannot be damaged.

10. Do not remove the plug from the socket by pulling

on the cable.

11. Do not pick up the unit by the cable.

12. Keep children and third parties away from the

workplace.

13. Keep tools in childsafe locations when not in use.

14. Do not overload the tool.

15. Do not use the tool to perform operations for

which it is not suitable.

16. Replace blunt tools in good time.

17. Visually inspect application tools to ensure they

are in good working order and suitable for the task

prior to setting up the job.

18. Fasten tools securely.

19. Clean the unit thoroughly following all work

20. Disconnect the plug from the power supply when

the unit is not in use, before performing

maintenance, tool replacement or repair work.

21. Only plug the unit in when the unit is switched off.

22. Always wear protective goggles (danger of tool

breakage).

23. If necessary, wear a protective dust mask.

24. Only use appropriate working clothes (no loose

sleeves, ties, jewellery).

1 2 3 4 5 6 7 8

Summary of Contents

Page 1

- 5 -14. MAINTAIN TOOLS WITH CARE. Keep tools sharpand clean for best and safest performance. Followinstructions for lubricating and changingaccessori

Page 2 - WARNING!

- 6 -25. Wear a hair net if you have long hair. 26. Only use accessories and spare partsrecommended by PROXXON 27. Observe the max. permitted rotation

Page 3 - Technical data

- 7 -Note:Keep this instruction manual in an easily accessibleplace. Only operate this machine if you are qualified todo so and follow the guidelines

Page 4 - Working with the scroll saw

- 8 -OperationBefore start-up:Mounting the machine The scroll saw must be fastened onto a sturdy woodenboard using the enclosed fixing bolts 1 (Fig. 2

Page 5 - Replacing the toothed belt

- 9 -Note: please remember that with a scroll saw, the saw bladefundamentally tries to follow the grain of the wood. Forfrequent even cuts, a circular

Page 6

- 10 -Notes

Page 7

- 11 -Notes

Page 8 - Spare parts list

- 12 -Part No.: Designation37088-01 Housing upper part37088-02 Housing lower part37088-03 Sliding door37088-04 Gear unit housing37088-05 Bearing bush